Argo AC Error Codes

AC BrandsArgo

Argo AC Error Codes

This air conditioning system meets strict safety and operating standards. As the installer or service person, it  is an important part of your job to install or service the  system so it operates safely and efficiently.

Error CodeFaults and Solutions
E01Error receiving of serial communications signal. Remote controller is detecting unusual signal from indoor unit.
E02Error transmitting of serial communications signal. Remote controller is detecting unusual signal from indoor unit.
E03Indoor unit is detecting unusual signal from the remote controller or group control.
E08Indoor unit address setting is duplicated. Improper setting of indoor unit or remote controller.
E09Remote controller address (RCU.ADR) is duplicated. Improper setting of indoor unit or remote controller.
E11Error receiving of serial communications signal. Indoor unit is detecting unusual signal from signal option.
E14When using flexible combination control, main indoor unit address setting is duplicated. (judged by outdoor unit.) Improper setting of indoor unit or remote controller.
E04Error receiving of serial communications signal. Indoor unit is detecting unusual signal from outdoor unit.
E05Error transmitting of serial communications signal. Indoor unit is detecting unusual signal from outdoor unit.
E06Error receiving of serial communications signal. Outdoor unit is detecting unusual signal from indoor unit.
E07Error transmitting of serial communications signal. Outdoor unit is detecting unusual signal from indoor unit.
E15No. of judged indoor units or total capacity of indoor units is small. Auto. address setting is not correct.
E16No. of judged indoor units or total capacity of indoor units is large. Auto. address setting is not correct.
E18Error receiving of serial communications signal. Indoor unit is detecting unusual signal from another indoor unit.
L02Model setting of indoor unit is not matching the outdoor unit. Improper setting of indoor unit or remote controller.
L03When using group control, main indoor unit address setting is duplicated. Improper setting of indoor unit or remote controller.
L07Improper wiring between indoor units. Improper setting of indoor unit or remote controller.
L09Capacity code of indoor unit is not set. Improper setting of indoor unit or remote controller.
L11Improper wiring of group control wiring. Improper setting of indoor unit or remote controller.

Argo AC Error Codes

Possible faults and solutions:

Do not attempt to repair the unit yourself. Improper repair can cause electric shocks or fire. Disconnect the unit from the power supply before contacting your local Technical Service Centre. Carry out the following checks Or Read All Of Argo Ac Error codes List before contacting your Technical Service Centre:

Fault: After That The indoor unit does not receive the signal from remote control or the remote control does not seem to be working

Check:

  1. Is there noticeable interference (e.g. static electricity, stable voltage)?
  2. Is the remote control within the signal reception range? Are there any obstacles between the remote control and the receiver?
  3. Is the remote control pointed at the receiver?
  4. Is the remote control’s sensitivity low? After That You Must See icons blurred or missing?
  5. Do icons fail to appear on the display when you operate the remote control?
  6. Is there a fluorescent light in the room Of After This problem?

Argo Ac Complete Trouble Shooting Method

Solution:

  1. After That Pull out the plug. After about 3 minutes reinsert the plug and restart the unit.
  2. The maximum signal reception distance is 8 m. The remote control will not work beyond this distance. Remove the obstacles.
  3. Point the remote control at the receiver on the indoor unit.
  4. Check the batteries. If the batteries are very low, replace them.
  5. Check if the remote control is damaged. If it is, replace it.
  6. Position the remote control next to the indoor unit. Turn off the fluorescent light and try again.

Fault: No air comes out of the indoor unit

Check:

  1. After This Kind Of Errors Is the indoor unit’s air inlet or outlet blocked?
  2. When You See This Type Of Things In heat mode, has the indoor temperature reached the set temperature?
  3. Has heat mode only recently been selected?

Solution:

  1. When You Face This problem Just Remove the obstruction.
  2. Once the set temperature has been reached, the indoor unit will stop blowing out air.
  3. To prevent blasts of cold air from being blown out, there will be a delay of several minutes before operation begins (this is normal).

Fault: The air conditioner is not working

Check:

  1. Is there a power cut?
  2. Has the plug come loose?
  3. Has the circuit breaker tripped or has the fuse blown?
  4. Is the wiring faulty?
  5. Was the unit restarted immediately after shutdown?
  6. Is the setting on the remote control correct?
  7. After All Of This Is Your Problem Not Solved Just Email Us We Are Active For You in Working Hours.

Leave a Reply

Your email address will not be published. Required fields are marked *

Fill out this field
Fill out this field
Please enter a valid email address.
You need to agree with the terms to proceed

You May Also Like

Akai AC Error Codes
Electric AC Error Codes

Subscribe to our Youtube Channel

Must Read

Menu